OV/OC Protection IC and Li+ Charger
Front-End Protection IC with LDO Mode Current
EHP2601
General Description
The EHP2601 is a charger front-end integrated circuit designed to provide protection to Li-ion batteries from failures of charging circuitry. The device monitors the input voltage, battery voltage and the charging current to make sure all three parameters are operated in normal range. The device will switch off internal MOSFET to disconnect IN to OUT to protect load when any of input voltage, output current exceeds the threshold. The Over temperature protection (OTP) function monitors chip temperature to protect the device. The EHP2601 also can protect the system’s battery from being over charged by monitors the battery voltage continuously. The device operates like a linear regulator, maintaining a 5.1V output with input voltages up to the input over-voltage threshold.
The EHP2601 is available in DFN-2x2-8L package. Standard products are Pb-free and Halogen-free.
Features
◆Maximum Input Voltage: 24V
◆Programmable OCP: Up to 1.5A
◆Input OVP: 6.8V
◆OVP Response Time: Less Than 1us
◆Battery OVP threshold: 4.35V (Typ.)
◆Over Temperature Protection
◆Soft-Start to Prevent Inrush Currents
◆LDO Mode Output: 5.1V
◆Fault Indication Output
◆Enable Input
◆High Immunity of False Triggering Under Transient
◆Thermal Enhanced DFN Package
◆RoHS Compliant and Halogen Free
Applications
◆GPS
◆MID
◆Car DVR
◆Digital Video
Typical Application Circuit
OV/OC Protection IC and Li+ Charger
Front-End Protection IC with LDO Mode Current
EHP2601
Pin Assignment
Pin Description
PIN |
SYMBOL |
I/O |
DESCRIPTTION |
1 |
IN |
Power | Input Power. Connected to external DC supply and bypass IN to VSS with a ceramic capacitor (1μF MIN). |
2 | GND | Ground | Power ground. Connect to the thermal pad and to the ground rail of the circuit. |
3 | NC | / | Not connected. |
4 | FAULT |
O | This is an open-drain logic output that turns LOW when any protection event occurs. |
5 | CE |
I | Chip Enable (Active Low). Pull this pin to low or leave it floating to enable the IC and force it to high to disable the IC. This is internally pulled down and pull-down resistor is about 200kΩ. |
6 |
VB |
I | Battery Voltage Sense Input. Connected to battery’s positive terminal through a 10kΩ resistor. |
7 |
ILIM |
O | Over current protection threshold setting pin. Connect a resistor between this pin and GND to set the OCP threshold:
|
8 |
OUT |
O | Output terminal to the charging system. Bypass OUT to VSS with a ceramic capacitor (1μF MIN). |
9 |
Expose Pad |
GND | Thermal pad electrically connected to GND pin internally. This pad must be soldered to a large PCB and connected to GND for maximum thermal dissipation. |
Ordering/ Marking Information
Package Type: F1:DFN2x2
R:Tape & Reel
PART NO | OVP TYPE | PACAKGE | TEMPERATURE | TAPE & REEL |
EHP2601NNF1R | 6.8V | DFN-2x2-8L | -40 ~ +85℃ | 4000/REEL |
Absolute Maximum Ratings (Note)
SYMBOL | ITEMS | VALUE | UNIT | |
IN | Input Voltage | -0.3~24 | V | |
OUT | Output Voltage | -0.3~7 | V | |
All other pins | -0.3~6 | V | ||
IOMAX | Output Load Current | 1.5 | A | |
ISINK | 15 | mA | ||
PDMAX | Power Dissipation*1 |
DFN-2x2-8L | 1 | W |
RθJA | Thermal Resistance*2 | 75 | ℃/W | |
TJ | Junction Temperature | -40~150 | ℃ | |
TSTG | Storage Temperature | -55 to 150 | ℃ | |
TSOLDER | Package Lead Soldering Temperature (10s) | 260 | ℃ | |
HBM | ESD Susceptibility, Human Body Model | 8 | KV | |
MM | ESD Susceptibility, Machine Model | 400 | V | |
CDM | ESD Susceptibility, Charged Device Model | 2 | KV |
Note: Exceed these limits might damage the device. Exposure to absolute maximum rating conditions may affect
device reliability.
*1: Surface mounted on FR-4 Board using 1 square inch pad size, dual side, 1oz copper.
*2: Power dissipation is calculated by PD = (VIN-VOUT) x IOUT
SYMBOL | ITEMS | VALUE | UNIT |
IN | Input Supply Voltage | 3.5 to 24 | V |
OUT | Output Current | 0.5~1 | A |
TOPR | Operating Temperature | -40 to +85 | ℃ |
Recommanded Operating Range
Electrical Characteristics
OV/OC Protection IC and Li+ Charger
Front-End Protection IC with LDO Mode Current
EHP2601
Simplified Block Diagram
Typical Performance Characteristics
OV/OC Protection IC and Li+ Charger
Front-End Protection IC with LDO Mode Current
EHP2601
OV/OC Protection IC and Li+ Charger
Front-End Protection IC with LDO Mode Current
EHP2601
OV/OC Protection IC and Li+ Charger
Front-End Protection IC with LDO Mode Current
EHP2601